Riverstone Networks RS 8000 Manual del operador Pagina 132
- Pagina / 158
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
4-24 Riverstone Networks RS 8000/8600 Switch Router Getting Started Guide
Using Redundant Control Modules Initial Configuration
4.9.2 Communicating with the Backup Control Module
There are two ways to establish communication with the backup CM: through the backup CM’s console port or through
a telnet session from the primary CM to the backup CM using the keyword
backup-cm
. For Instance, the following
example shows a telnet session from the primary CM to the backup CM.
Notice in the example above that the prompt displays a dollar sign (
$
). This indicates that the display belongs to the
backup CM. The dollar sign also appears if you connect to the backup CM through its console port.
When connected to the backup CM (either through telnet or the console) you are provided with only a sub-set of the
commands available on the primary CM.
telnet RS1
----------------------------------------------------------------------
RS 8000 System Software, Version 8.0
Copyright (c) 2000-2001 Riverstone Networks
System started on 2001-04-24 09:37:35
----------------------------------------------------------------------
Press RETURN to activate console . . .
rs1> enable
rs1#
rs1# telnet backup-cm
Trying 127.0.0.1, port 10130 ...
Connected to 127.0.0.1.
Escape character is '^]'.
----------------------------------------------------------------------
RS 8000 System Software, Version 8.0
Copyright (c) 2000-2001 Riverstone Networks, Inc.
System started on 2001-04-19 14:40:57
----------------------------------------------------------------------
Press RETURN to activate console . . .
rs1>$
- RS 8000/8600 1
- Switch Router 1
- Getting Started Guide 1
- COPYRIGHT NOTICES 2
- RADIACIÓN LÁSER Y CONECTORES 6
- RIVERSTONE NETWORKS, INC 9
- AGREEMENT 9
- RIVERSTONE STANDARD WARRANTY 11
- TABLE OF CONTENTS 15
- LIST OF FIGURES 19
- LIST OF TABLES 21
- 1 ABOUT THIS GUIDE 23
- 2 INTRODUCTION 25
- 2.2 SPECIFICATIONS 26
- Introduction Specifications 27
- 2.3 SOFTWARE OVERVIEW 28
- IP Routing 29
- IP Multicast Routing 29
- IPX Routing 29
- 2.3.9 Web Hosting Features 32
- 2.3.10 Management Platforms 32
- 2.4 HARDWARE OVERVIEW 33
- Switching Fabric 34
- Power supply 34
- 2.4.2 Backplane 35
- 2.4.3 Fan Module 35
- 2.4.4 Control Module 35
- Boot Flash 36
- Memory Module 36
- 100-125~5A 38
- 200-240~3A 38
- 50-60 Hz 38
- 100-125V~ 10A 39
- 200-240V~ 6A 39
- 50/60 Hz 39
- 2.4.6 DC Power Supply 40
- 10/100BASE-TXG8M-HTXA2-08 42
- 87654321 44
- 10/100BASE-TXG8M-HTXB2-16 45
- 100BASE-FXG8M-HFXA1-08 47
- 100Base-FX SFP Line Card 48
- 1000Base-SX Line Card 49
- 1000BASE-SXG8M-GSXB1-02 50
- 1000Base-LX Line Card 52
- 1000Base-LLX Line Card 54
- 1000Base-T Line Card 55
- Multi-Mode Short-Reach 58
- Single-Mode 58
- Long-Reach (70 Km) 58
- ATM Multi-Rate Line Card 63
- ATM OC-12c Line Card 64
- ATM-OC-12c-SMFG8M-A12B9-02 65
- POS OC-3 MMFG8M-PO3B1-04 66
- POS OC-3 SMFG8M-PO3B9-04 66
- POS OC-12c SMFG8M-P12B9-02 68
- G8M-PO3MM-02 69
- POS MPLS OC3 69
- G8M-P12MM-02 70
- POS MPLS OC-12c/STM-4 70
- Quad Serial - CEG8M-SECAC-04 71
- Dual HSSI 73
- G8M-HSIAC-02 73
- CMTS Line Card 75
- DOCSIS CMTSG8M-CMTSNA-6X1 76
- Multi-Rate WAN Line Card 77
- Channelized T3 Line Card 80
- CHANNELIZED T3G8M-CT3BB-02 81
- 18-695-01 82
- Figure 2-44 SRP bridge module 83
- 3 HARDWARE INSTALLATION 87
- 3.3 INSTALLING THE HARDWARE 88
- 3.2 HARDWARE SPECIFICATIONS 88
- Internal Power Supply One 94
- Internal Power Supply Two 94
- RS 8600 DC Power Supply 94
- Card Guides 96
- Circuit Board 96
- Metal Plate 96
- To remove 100
- Make sure WIC is aligned 104
- Insert the WIC through the 104
- (Base Slot) 105
- G8M-SRP-MATE 106
- Insert SFP into ports 107
- 4 INITIAL CONFIGURATION 109
- If the message “ 111
- 4.2.1 CLI Access Modes 112
- CONFIGURATION FILE 114
- 4.5 SETTING UP PASSWORDS 120
- Here is an example: 122
- 4.6 SETTING UP SNMP 123
- 4.6.2 Improving SNMP Security 124
- 4.6.3 Supported MIBs 125
- KRVWQD PH RU,3DGGU! 129
- IDFLOLW\W\SH! 129
- 4.9.1 Fail Over 131
- Software/Hardware Versions 134
- Changing Mastership 134
- Hot-Swapping 134
- 5 MANAGING SOFTWARE 135
- Reboot the RS 139
- Enter the 139
- 5.4 HITLESS SOFTWARE UPGRADE 143
- 5.4.1 Hitless Upgrade Example 144
- 5.5 UPGRADING FPGA CODE 146
- APPENDIX A TROUBLESHOOTING 149
- INFORMATION 151
- Numerics 153
Relacionado con productos y manuales para Redes Riverstone Networks RS 8000
Redes Riverstone Networks WICT1-12 Especificaciones
(111 paginas)
(111 paginas)
Redes Riverstone Networks RS 8000 Manual de usuario
(23 paginas)
(23 paginas)
Redes Riverstone Networks RS 8000 Guía de usuario
(718 paginas)
(718 paginas)
Redes Riverstone Networks RS 2100 Especificaciones
(120 paginas)
(120 paginas)
Redes Riverstone Networks WICT1-12 Especificaciones
(77 paginas)
(77 paginas)
Redes Riverstone Networks RS 2100 Manual de usuario
(16 paginas)
(16 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.039 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales